Round & Shaped Punches, Dies, C-Frame Units


	Manufacturers of ‘Minni-Die’ C-Frame unitised hole punching, notching & cropping tools


	for sheet metals, roll formed sections, aluminium extrusions, tubes & plastics


	40 Trent South Industrial Park, Little Tennis Street, Nottingham.

Nottinghamshire. ENGLAND. NG2 4EQ. U.K.

Tel Int +44 (0)115 941 9009 Fax Int +44(0)115 950 3921 Mobile: +44(0)7860 351 648

Used in Press Brakes, Mechanical Presses, Hydraulic Presses & Custom built hole punching machines

28/04/2008 07:15am

Best viewed at 800 x 600 in explorer 5 / 6

ROUND PUNCHES & DIES from stock

Model M10 & Model M14 standard punches and dies to suit any metal thickness up to 6mm - mild steel - stainless - aluminium - copper - brass. These sizes in bold are normally available ex-stock but intermediate sizes can be specified at no extra cost and 2-3 days longer See chart of sizes below:-

diam

metal thickness

mm	1mm	2mm	3mm	4mm	5mm	6mm
punch	dies	dies	dies	dies	dies	dies
3,0	32	34	36
3,2	34	36	38
3,4	36	38	40
3,6	38	40	42
3,8	40	42	44
4,0	42	44	46	48
4,2	44	46	48	50
4,4	46	48	50	52
4,6	48	50	52	54
4,8	50	52	54	56
5,0	52	54	56	58	60
5,2	54	56	58	60	62
5,4	56	58	60	62	64
5,6	58	60	62	64	66
5,8	60	62	64	66	68
6,0	62	64	66	68	70	72
6,2	64	66	68	70	72	74
6,4	66	68	70	72	74	76
6,6	68	70	72	74	76	78
6,8	70	72	74	76	78	80
7,0	72	74	76	78	80	82
7,2	74	76	78	80	82	84
7,4	76	78	80	82	84	86
7,6	78	80	82	84	86	88
7,8	80	82	84	86	88	90
7,9	81	83	85	87	89	91
8,0	82	84	86	98	90	92
8,3	85	87	89	91	93	95
8,5	87	89	91	93	95	97
8,7	89	91	93	95	97	99
8,9	91	93	95	97	99	101
9,0	92	94	96	98	100	102
9,3	95	97	99	101	103	105
9,5	97	99	101	103	105	107
9,7	99	101	103	105	107	109
9,9	101	103	105	107	119	11
10,0	102	104	106	108	110	112

Ex-stock popular punch sizes are shown in bold type


	Typical illustration of Models M10 to M30 punch head types of unit

Model M14

The chart on the right hand side shows the continued list of stock punches and dies for Model M14 from 10,2mm diameter through to 14,0mm diameter. All punch sizes in bold are available ex-stock and all dies are available for punching metal thicknesses up to 6,mm

Model M20 punches and dies start from punch diameter 11,1mm through to 20,0mm diameter but only the bold punch sizes are normally ex-stock.

Model M30 punches and dies from stock hard blanks, begin at 15,0mm diameter through to 30mm diameter.


	Specify: (1) Model No XX, (2) punch diameter, (3) The metal thickness, (4) the die number from the chart. The sizes in the chart on the left of the page apply to both the Models M10 and M14 so the model number MUST be specified when ordering punches and dies.

diam

metal thickness

mm	1mm	2mm	3mm	4mm	5mm	6mm
punch	dies	dies	dies	dies	dies	dies
10,3	105	107	109	111	113	115
10,5	107	109	111	113	115	117
10,7	109	111	113	115	117	119
10,9	111	113	115	117	119	121
11,1	113	115	117	119	121	123
11,3	115	117	119	121	123	125
11,5	117	119	121	123	125	127
11,7	119	121	123	125	127	129
11,9	121	123	125	127	129	131
12,1	123	125	127	129	131	133
12,3	125	127	129	131	133	135
12,5	127	129	131	133	135	137
12,7	129	131	133	135	137	139
12,9	131	133	135	137	139	141
13,1	133	135	137	139	141	143
13,3	135	137	139	141	143	145
13,5	137	139	141	143	145	147
13,7	139	141	143	145	147	149
13,9	141	143	145	147	149	151
14,0*	142	144	146	148	150	151
14,2	144	146	148	150	152	154
14,4	146	148	150	152	154	156
14,6	148	150	152	154	156	158
14,8	150	152	154	156	158	160
15,0	152	154	156	158	160	162
15,2	154	156	158	160	162	164
15,4	156	158	160	162	164	166
15,6	158	160	162	164	166	168
15,8	160	162	164	166	168	170
16,0	162	164	166	168	170	172
16,2	164	166	168	170	172	174
16,4	166	168	170	172	174	176
16,6	168	170	172	174	176	178
16,8	170	172	174	176	178	180
17,0	172	174	176	178	180	182
17,2	174	176	178	180	182	184
17,4	176	178	180	182	184	186
17,6	178	180	182